When you ’re building a fencing around your grand , there are many different types from which to take . Ideally , the fence will complement your home ’s exterior . For exercise , a stucco fencing works well with a stucco nursing home . If you do n’t desire a solid stucco fence surrounding your family , you may erect mainstay constructed of concrete and cross them with stucco , then complete the fencing with wrought - iron railings .
Step 1
Drive stakes into the ground and tie drawstring to them to grade the fence line . Mark the localisation of the pillars on the ground along the fencing line , keep spacing them according to the lengths of iron rail off you have selected .
Step 2
labour a hole 8 inches deep and 2 foot square for each column . dismantle the dirt inside the holes .
Step 3
Pour 2 inch of gravel into each kettle of fish , then dismantle it and tamp it to pack together the basis .
Step 4
Mix concrete come the manufacturer ’s instructions and replete each muddle with concrete . Smooth the surface by embroil a 2 - by-4 board across the top of the concrete . Allow the concrete to cure for at least four day .
Step 5
Step 6
Mix mortar for the clinker blocks , and place it around the circumference of the concrete base , apply it wide enough to encompass the breadth of the clinker blocks . Apply a layer 1/2 - inch duncical .
Step 7
Set the first clinker block into the howitzer , and place a degree on top of it . Adjust it , if necessary , to make the pulley block story .
Step 8
practice 1/2 inch of mortar to the side of the clinker block that is not on the sharpness of the slab , and commit another clinker pulley-block in the howitzer on the slab against the first mental block , keep it level with the first closure . When placing the 2nd pulley-block , rotate it so that it form a 90 - grade angle with the first closure . Lay two more blocks on the slab using the same technique . When complete , there will be four blocks around the margin of the slab , with a minuscule , open field in the center .
Step 9
Step 10
Continue lay blocks until you make the hope height for the column . Stagger the blocks in each words so that the joints in consecutive rows are not aligned . fabricate all of the pillars using the process . Allow the mortar to set for the time specialise on the packaging .
Step 11
Spray the pillar with a hosiery to stifle the clinker blocks . Adding moisture to the blocks prevent them from drawing moisture out of the stucco as it cures , which can cause the stucco to collapse .
Step 12
immix a batch of stucco using 4 parts sand and 1 part trench mortar , stirring it until it has the consistency of mashed spud .
Step 13
Step 14
set two scoops of stucco onto a hawk — a metal tray that contains a handle gallop from the bottom of the tray and is used when applying stucco and plaster .
Step 15
broadcast the stucco onto one side of the first pillar , starting at the bottom of the pillar and working toward the top . Apply a layer of stucco about 1/4 - inch thick to each side of the pillar .
Step 16
pass over a quick study trowel over the surface of the stucco with circular gesture to help prevent the stucco from cracking . Scratch grooves into the stucco with a cockscomb - similar tool called a scarifier . The grooves will help the top coat of stucco stick to the base pelage .
Step 17
Apply the base coating of stucco to all pillar , and allow it to gear up for the clip specify on the packaging .
Step 18
Step 19
commix the top coat of stucco using 3 parts stucco sand , 1 part cement , and pigment to color the stucco .
Step 20
spread over the pillars with the top coat of stucco , using the same process you used for the base coating . Apply the top coat in a layer 1/2 in to 3/4 inch deep . encompass the mainstay with credit card for six to eight workweek as the stucco cures . Every few days , remove the plastic to spray the stucco with a tripping mist to keep it damp , then cover the pillar again .
Installing the Railings
cadence and pock the top boundary of the railing on each side of the pillars at the height you want the fence .
Hold the railings in place between the tower with the help of an assistant and mark the bolt hole for the railings on the pillar .
Drill pilot hole into the tower where you score them for bolt holes , using a hammer drill meet with a Freemasonry drill bit .
murder the thunderbolt from the concrete sleeve anchors and slide the sleeves into the hollow in the pillars . If you experience trouble , tap them into the tower with a hammer until the control surface is flush with the column .
Lift the first section of vilify into attitude between two pillars , aligning the bolt hole on the railing with the holes in the pillars . run off the railings into position by tightening them with a socket twist . Do n’t overtighten the bolts , however , as doing so can split up the anchor sleeve .
add the balance of the rail , using the same process .
